OLYMPUS DIGITAL CAMERA

Eric Singer, creator of musical robots and maestro of LEMUR, the League of Electronic Musical Urban Robots, has unveiled a new wireless sensor-to-MIDI interface. It’s quite a bit pricier than the non-wireless MIDI models at US$495, but the payoff is a complete kit for wireless performance that promises to be resistant to both latency and interference. The receiver can be connected via either USB or MIDI, and the sensor unit has 20 inputs which you can mix and match as up to 10 analog ins and 20 digital ins. Put the sensor/transmitter unit wherever you like, then transmit data wirelessly to the receiver — so the sensors could be strapped to a dancer while a computer or synth receives the data elsewhere.

I hope to have a hands-on demo soon, but in the meantime, here are the specs — just in case that wireless project can’t wait any longer.

  • Small transmitter (2 5/8″ x 1 1/2″ x 1 1/2″); encloses internal antenna and 9v battery
  • Can be worn on body
  • 1000 foot range under ideal conditions; several hundred foot range possible even with obstructions
  • Uses 900 MHz frequency band for less interference than the increasingly crowded 2.4 GHz band [Ed. What, you don't like interference each time you microwave a burrito, really?]
  • Uses highly reliable RF chip set proven in live performance situations
  • Eight selectable channels allow eight units to be used simultaneously or channel switching if interference is encountered
  • Continuous re-transmit of sensor values virtually eliminates drop-out or lost data
  • Very low latency transmit (maximum 7 ms with all sensors enabled)
  • Very low latency USB and MIDI output (actual latency system dependent)
  • Normal (7-bit) and high (10-bit) resolution analog modes available
  • Easily configured with menu-driven programming patch
  • No network configuration required as with Bluetooth or WiFi
  • Standard MIDI and USB-MIDI input/output ports
  • With USB, appears on computer as a standard MIDI device with no special drivers required
  • Once configured, can be used as a standalone MIDI device without a computer
  • Several interchangeable styles of connector boards allow flexibility in making sensor connections
  • Three-pin style connector board allows direct interfacing of popular sensors available from other manufacturers

If you still like wires, the US$149 original MidiTron remains an option (along with, of course, open hardware like the Arduino and such).

Miditron @ Eroktronix

  • cubestar

    I have absolutely no DIY skills, but would like to use something like this.

    I had been looking at the Eobody Eowave 2 because it is already put together and is a breakout box you just plug cables into.

    I'm guessing that with this, you would have to obtain your own breakout box and components and solder them together?

  • http://www.createdigitalmusic.com Peter Kirn

    No, you've got the box right here for attaching sensors, that's not a problem. You'll need to acquire sensors, yes, but that's no big deal … super easy soldering there, just to make permanent whatever it is you're doing. I think this also winds up being cheaper than the Eowave, too.

    What I'm kind of curious about, though, is how this compares to some of the other wireless solutions out there … some of which may require more work but could be more affordable. I'm guessing it'll depend mostly on the project which you'd choose, but I'll try to do a survey of what's out there soon.

  • Pingback: Wireless Sensor Networks » Blog Archive » MidiTron Wireless: Make Your Own Wireless Sensor-to-MIDI Project

  • cubestar

    The Eowave is $300 w/usb or $350-ish with usb & midi.

    So how do the sensors actually connect to the miditron?

    Are there 1/8 sockets or something I'm not seeing?

  • http://www.createdigitalmusic.com Peter Kirn

    Oops… then I'll definitely have to take another look at the Eowave, being that much cheaper. As for the connections, I see screw terminals in the picture, plus "three-pin connectors" for compatibility with various sensors. In terms of how this all fits together, I'll have a look at it with Eric I hope in a couple of weeks (he's also in NYC.)

  • cubestar

    Of course, the EoWave is not wireless, not that I'm sure if that matters for my use…

    I'm just afraid I would get something like the miditron and never get it all working, there's a guy on the Ableton posting and he's having to make simple circuits to get the levels working…

    Thanks for the info, Peter!

  • spanky

    is the EoWave wireless??

    cause it doesn't say